Are you trying to locate tips about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is conveniently obtainable, the project can move rapidly; if you have to open a wall to remove the old bathtub as well as place the new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your washroom if you have currently gotten a new tub and also do not need to transform the plan of your previous water supply pipelines.
Your devices as well as product list must comprise the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bath needs to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for position. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the water system and also examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the bathtub should wait until the bath tub has been made use of at the very least when as this will settle it right into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The former type ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in use. The sealant can crack relatively early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about Tools You Need to Install a New Bathtub ? Give a remark directly below. We would be delighted to know your thinking about this page. Hoping that you visit us again later on. Are you aware of somebody else who is truly interested in the topic? Be sure promote it. Thanks so much for taking the time to read it.
Quality-driven emergency plumbing solutions.